Difference between revisions of "Serial communication with Matlab"
ScottMcLeod (talk | contribs) |
|||
Line 21: | Line 21: | ||
The wiring diagram for serial communication is shown below. There are three basic components in this setup. The potentiometer serves as an analog input to the PIC, which is converted to a digital signal through the PIC's analog to digital converter pin. The MAX232N level converter provides bidirectional voltage shifting for digital communication between the PIC and PC (read more about this chip and level conversion on the RS232 wiki [http://hades.mech.northwestern.edu/wiki/index.php/PIC_RS232 here]). Finally, the female DB-9 connector allows the circuit to connect to the PC's serial port. |
The wiring diagram for serial communication is shown below. There are three basic components in this setup. The potentiometer serves as an analog input to the PIC, which is converted to a digital signal through the PIC's analog to digital converter pin. The MAX232N level converter provides bidirectional voltage shifting for digital communication between the PIC and PC (read more about this chip and level conversion on the RS232 wiki [http://hades.mech.northwestern.edu/wiki/index.php/PIC_RS232 here]). Finally, the female DB-9 connector allows the circuit to connect to the PC's serial port. |
||
[[Image: |
[[Image:Team26-SerialComCircuit.jpg]] [[Image:P1120664.JPG |Thumb|640x470 px|Image of wiring for serial communication between PIC 18F4520 and PC]] |
||
The data sheet for the MAX232 can be found here: [http://rocky.digikey.com/WebLib/Texas%20Instruments/Web%20data/MAX232,232I.pdf http://rocky.digikey.com/WebLib/Texas%20Instruments/Web%20data/MAX232,232I.pdf] |
The data sheet for the MAX232 can be found here: [http://rocky.digikey.com/WebLib/Texas%20Instruments/Web%20data/MAX232,232I.pdf http://rocky.digikey.com/WebLib/Texas%20Instruments/Web%20data/MAX232,232I.pdf] |
Revision as of 17:36, 6 February 2008
Original Assignment
Matlab has a "serial" function that allows it to communicate through a serial port. This project is to establish serial port connection with the PIC and demonstrate bidirectional communication between the PIC and a Matlab program, using, for example, a USB to RS232 adapter and level shifter chip. The Matlab program could simply log data from the PIC (e.g., the angle of a potentiometer knob), or plot it on a user interface in real time. Keystrokes from the user of the Matlab program should be obviously received by the PIC, perhaps by lighting the LEDs on the PIC board.
Overview
Matlab has a "serial" function that allows it to communicate through a serial port. This project is to establish serial port connection with the PIC microcontroller and demonstrate bidirectional communication between the PIC and a Matlab program. For demonstration purposes, the PIC will send digital potentiometer readings to Matlab as well as receive keystrokes from the Matlab user to light up LEDs on its circuit board.
A USB to RS232 adapter and level shifter chip were used to connect the computer to the PIC. In this lab, we used a cheap cable found at http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=220199148938&ih=012&category=41995&ssPageName=WDVW&rd=1
**Important! DO NOT connect the serial Rx/Tx lines DIRECTLY to the PIC!!!**
A level shifter chip is necessary to convert the high and low logic voltages from the desktop computer (+12V/-5V) to (+5V,0V) for the PIC. A standard RS232 connection is called a DB9 connector and follows the pin diagram shown here: http://www.aggsoft.com/rs232-pinout-cable/serial-cable-connections.htm This cable requires 1 driver installation as included on the mini-cd. To install this driver, you must first plug in the USB cable, and run the installation program located in the <CDROM>/. To configure the Matlab script to connect to the proper serial port, use the device manager (Right click My Computer->manage) and expand the section Ports. Here you will see USB- make a note of the COM number. In our program, our serial port was COM14.
A female DB9 connector was wired to our level shifter to convert the voltages, with the level shifter connected to our PIC. Refer to the Circuit section for details.
The PIC was programmed with our C code as shown below. Our program was designed to read a potentiometer through the PIC's ADC (Analog to Digital Converter) port and transmit the digitized readings over the serial cable to the PC (upon request). In Matlab, if a users sends data to the PIC by entering a character, the PIC responds with the current potentiometer reading and the last received byte from the PC. The PIC is also programmed to display the character received from the PC on its LED array (D register) as a 8-bit ASCII number. The programs can easily be modified to create any custom protocol, but are designed to show simple 2-way communication between Matlab and the PIC.
Circuit
The wiring diagram for serial communication is shown below. There are three basic components in this setup. The potentiometer serves as an analog input to the PIC, which is converted to a digital signal through the PIC's analog to digital converter pin. The MAX232N level converter provides bidirectional voltage shifting for digital communication between the PIC and PC (read more about this chip and level conversion on the RS232 wiki here). Finally, the female DB-9 connector allows the circuit to connect to the PC's serial port.
The data sheet for the MAX232 can be found here: http://rocky.digikey.com/WebLib/Texas%20Instruments/Web%20data/MAX232,232I.pdf
PIC Code
/* SerialComm.c Scott McLeod, Sandeep Prabhu, Brett Pihl 2/4/2008 This program is designed to communicate to a computer using RS232 (Serial) Communication. The main loop of this program waits for a data transmission over the Serial port, and responds with a current reading of an analog input (potentiometer) and the last received data. Note the analog input is only for testing purposes, and is not necessary for serial communication. Lines unnecessary for RS232 communication are commented with enclosing asterisks ('*..*'). */ #include <18f4520.h> #fuses HS,NOLVP,NOWDT,NOPROTECT #DEVICE ADC=8 // *set ADC to 8 bit accuracy* #use delay(clock=20000000) // 20 MHz clock #use rs232(baud=19200, UART1) // Set up PIC UART on RC6 (tx) and RC7 (rx) int8 data_tx, data_rx = 0; // Set up data_tx (transmit value), data_rx (recieve value) void main() { setup_adc_ports(AN0); // *Enable AN0 as analog potentiometer input* setup_adc(ADC_CLOCK_INTERNAL); // *the range selected has to start with AN0* set_adc_channel(0); // *Enable AN0 as analog input* delay_us(10); // *Pause 10us to set up ADC* while (TRUE) { data_tx = read_adc(); // *Read POT on analog port (0-255)* output_d(data_rx); // Output last recieved value from computer delay_ms(10); if (kbhit()) // If PIC senses data pushed to serial buffer { data_rx = fgetc(); // Read in recieved value from buffer printf("Pot: %u Char: %u\n", data_tx, data_rx); // Once data sent and read, PIC sends data back delay_ms(100); } } }
Matlab Code
% SerialComm.m Scott McLeod, Sandeep Prabhu, Brett Pihl 2/4/2008 % This program is designed to communicate to a PIC 18F4520 via RS232 (Serial) Communication. % % The main loop of this program waits for a character input from the user, % upon which it transmits the ascii value and waits for data to be written. s = serial('COM14','BAUD',19200); % Create serial object (PORT Dependent) fopen(s) % Open the serial port for r/w myChar = 'a'; prompt = 'Enter a character (q to exit): '; while (myChar ~= 'q') % While user hasn't typed 'q' myChar = input(prompt, 's'); % Get user input fprintf(s, '%s', myChar(1)) % Write first char of user input to serial port fprintf(fscanf(s)) % Read Data back from PIC end fclose(s); % Close the serial port delete(s); % Delete the serial object
If your program doesn't close and delete the serial port object correctly, you can use the command shown below to delete all of the serial port objects.
delete(instrfind)