PIC32MX: High-speed Wireless Communication
Original Assignment
Do not erase this section!
Your assignment is to create the circuit and code that allows two PIC32s to use wireless communication at high speeds using the Transceiver nRF24L01+ Module with Chip Antenna from Sparkfun.
Read up on the nRF24L01+ Module commands and create functions to allow a PIC32 to initialize and send and receive data.
Test your code by sending 1000 bytes of data from one PIC32 to the other and echo the data back. How long does this transmission take? How far can you separate the PIC32s before the transmission is unreliable?
Overview
Note: THIS SYSTEM/CODE DOES NOT WORK!
The goal of this project is to transmit a byte of data (e.g. a character) from one PIC32/nRF24L01+ board to the other board, and display the received character on a PC screen.
This wiki describes how to wire a nRF24L01+ chip ("wireless chip") to the transmitting PIC32 board ("transmitter") and receiving PIC32 board ("receiver"), and includes annotated code describing the functions that facilitate the wireless communication.
To operate the system, you must properly connect the wireless chips to the PIC32s, load the transmitter code onto the PIC that you wish to act as a transmitter, load the receiver code onto the PIC that you wish to act as a receiver, properly connect an RS232 cable to the PIC and open a serial communication program (e.g. HyperTerminal or putty), and turn the NU32 boards on. If the system works, the receiver should print "rec data = x" on the screen.
Possible Explanation of Errors
We tried to debug our system from multiple directions. We triple-checked the wiring, following the Sparkfun tutorials, performed loopback test on the SPI channel, and verified IRQ status register using the onboard LEDs.
Circuit
The wireless chip has 8 pins that need to be wired to the PIC:
(1) Vcc -> +3.3 Vdc supply
(2) CE -> uC pin PORTC.1, configured as GPIO/input
(3) CSN -> uC pin PORTC.2, configured as GPIO/output
(4) SCK -> uC pin PORTC.3/SCK, configured as SCK(SPI)/output
(5) MOSI -> uC pin PORTC.5/SDO, configured as SDO(SPI)/output
(6) MISO -> uC pin PORTC.4/SDI, configured as SDI(SPI)/input
(7) IRQ -> uC pin PORTB.0, configured as GPIO/input
(8) GND -> common digital ground
The +3.3V and ground are provided by the NU32 board. The term "uC" above stands for microcontroller, which is the PIC32 in our case. GPIO stands for General Purpose Input/Output.
Descriptions of the wireless chip's pins can be found in Brennan Ball's DIYembedded Tutorial 0. The SCK, MOSI, and MISO pins interface with the SPI on the PIC32 which allows for communication between the PIC and the wireless chip. The GPIO pins will be initialized as digital inputs or outputs in the code to enable/disable the wireless chip and check the wireless data transfer/receive stats.
In order to print information from the PIC to the PC, we need to wire an PIC_RS232 cable's transfer and receive lines to the UART ports of the NU32 board (F4, F5).
Code
Besides the main C files for the transmitter and receiver, the project also needs the nRF24L01.h header file and C file in addition to the hardware header and linker files. Download the nRF24L01+ header files.
Transmitter Code
// **************************************************************
/*
WirelessTransmitter.c
Lab 5: High-speed Wireless Communication
Jonathan Drake, Caitlin Ramsey
2010-02-16
This code initializes the nRF24L01+ chip as a transmitter and
continuously transmits a character every 100ms. The loop contains
code to both output the program's status to the PC via RS232
cable and onboard LEDs.
*/
// **************************************************************
// Includes
#include "HardwareProfile.h"
#include "nrf24l01.h"
// Function Declarations
// Note: Descriptions of functions found after main() function
void Initialize(void);
void InitializeIO(void);
void SpiInitDevice(int chn, int isMaster, int frmEn, int frmMaster);
void initUART2(int pbClk);
unsigned char spi_send_read_byte(unsigned char byte);
void Delayms( unsigned t);
void Delayus( unsigned t);
void Delaytus( unsigned t);
// Constants
#define DESIRED_BAUDRATE (19200) // The desired BaudRate for RS232 communication w/ UART
// Main Function
int main(void) {
Initialize(); // initialize onboard LEDs, IO pins, UART2, SPI1, set up nRF24L01+ as TX
char RS232_Out_Buffer[64]; // buffer for printing data to the screen via UART
unsigned char data = 'x'; // char to be transmitted
// print char to screen
sprintf(RS232_Out_Buffer, "data to send = %c\r\n", data);
putsUART2(RS232_Out_Buffer);
while(1)
{
putsUART2("...\r"); // print ... to show transmission
nrf24l01_irq_clear_all(); //clear all interrupts in the 24L01
nrf24l01_set_as_tx(); // force 24L01 to be a transmitter (this is a double-check)
//transmit received char over RF, length = 1 byte, true = send away
nrf24l01_write_tx_payload(&data, 1, true);
// is the 24L01 activated?
if (nrf24l01_irq_pin_active()) {
mLED_1_On();
} else {
mLED_1_Off();
}
// is the 24L01 an active transmitter?
if (nrf24l01_irq_tx_ds_active()) {
mLED_2_On();
} else {
mLED_2_Off();
}
// wait until the packet has been sent or the maximum number of retries has been reached
while(!(nrf24l01_irq_pin_active() && nrf24l01_irq_tx_ds_active()));
// toggle onboard LED 3 to indicate loop iterating
mLED_3_Toggle();
Delayms(100);
}
}
// Initialize all initialize functions (function descriptions to follow)
void Initialize(void) {
// initialize peripheral bus clock to SYS_FREQ (80 MHz)
int pbClk;
pbClk = SYSTEMConfigPerformance(SYS_FREQ);
// initialize UART
initUART2(pbClk);
// initialize input/output pins
InitializeIO();
// initialize the SPI channel 1 as master, no frame mode
SpiInitDevice(1, 1, 0, 0);
//initialize 24L01 to debug configuration as transfer, 1 byte data size, and auto-acknowledge mode disabled
nrf24l01_initialize_debug(false, 1, false);
// initialize all onboard LEDs on NU32
mInitAllLEDs();
// if program initialized correctly, indicate on PC & onboard LEDs
putsUART2("\r\n***** System Initialized *****\r\n");
mLED_0_On();
}
// initialize IO pins
void InitializeIO(void) {
TRISBbits.TRISB0 = 1; // set IRQ pin as input
TRISC = 0xFFF9; // make CSN, CE digital outputs
PORTC = 0x0004; // set CSN bit active
}
// initialize UART2
void initUART2(int pbClk) {
#define config1 UART_EN | UART_IDLE_CON | UART_RX_TX | UART_DIS_WAKE | UART_DIS_LOOPBACK | UART_DIS_ABAUD | UART_NO_PAR_8BIT | UART_1STOPBIT | UART_IRDA_DIS | UART_DIS_BCLK_CTS_RTS| UART_NORMAL_RX | UART_BRGH_SIXTEEN
#define config2 UART_TX_PIN_LOW | UART_RX_ENABLE | UART_TX_ENABLE | UART_INT_TX | UART_INT_RX_CHAR | UART_ADR_DETECT_DIS | UART_RX_OVERRUN_CLEAR
OpenUART2( config1, config2, pbClk/16/DESIRED_BAUDRATE-1); // calculate actual BAUD generate value.
ConfigIntUART2(UART_INT_PR2 | UART_RX_INT_EN);
}
// initialize SPI
void SpiInitDevice(int chn, int isMaster, int frmEn, int frmMaster) {
unsigned int config = SPI_CON_MODE16|SPI_CON_SMP|SPI_CON_ON; // SPI configuration word
if(isMaster)
{
config|=SPI_CON_MSTEN;
}
if(frmEn)
{
config|=SPI_CON_FRMEN;
if(!frmMaster) {
config|=SPI_CON_FRMSYNC;
}
}
SpiChnOpen(chn, config, 4); // divide fpb by 4, configure the I/O ports. Not using SS in this example
}
// ******************************************************
/*
Function: spi_send_read_byte
Inputs: unsigned char byte
Outputs: unsigned short rxData
This function is required by the 24L01 header file.
It takes the inputted byte, sends it over the chosen
SPI channel, then waits to retreive data back.
*/
// ******************************************************
unsigned char spi_send_read_byte(unsigned char byte) {
unsigned short txData, rxData; // transmit, receive characters
int chn = 1; // SPI channel to use (1 or 2)
txData = byte; // take inputted byte and store into txData
SpiChnPutC(chn, txData); // send data
rxData = SpiChnGetC(chn); // retreive over channel chn the received data into rxData
return rxData;
}
// ******************************************************
/*
Functions: Delayms, Delayus
Inputs: unsigned t
Outputs: none
These functions are required by the 24L01 header file.
They take an input of t (ms, us) and delay the
program.
*/
// ******************************************************
void Delayms( unsigned t) {
// This uses Timer 1, can be changed to another timer. Assumes FPB = SYS_FREQ
OpenTimer1(T1_ON | T1_PS_1_256, 0xFFFF);
while (t--)
{ // t x 1ms loop
WriteTimer1(0);
while (ReadTimer1() < SYS_FREQ/256/1000);
}
CloseTimer1();
} // Delayms
void Delayus( unsigned t) {
OpenTimer1(T1_ON | T1_PS_1_256, 0xFFFF);
while (t--)
{ // t x 1ms loop
WriteTimer1(0);
while (ReadTimer1() < SYS_FREQ/256/1000000);
}
CloseTimer1();
} // Delayus
Receiver Code
// **************************************************************
/*
WirelessReceiver.c
Lab 5: High-speed Wireless Communication
Jonathan Drake, Caitlin Ramsey
2010-02-16
This code initializes the nRF24L01+ chip as a receiver to
continuously listen over its wireless antenna. If data is
received, the program prints the data on a PC. The loop contains
code to both output the program's status to the PC via RS232
cable and onboard LEDs.
*/
// **************************************************************
// Includes
#include "HardwareProfile.h"
#include "nrf24l01.h"
// Function Declarations
// Note: Descriptions of functions found after main() function
void Initialize(void);
void InitializeIO(void);
void SpiInitDevice(int chn, int isMaster, int frmEn, int frmMaster);
void initUART2(int pbClk);
unsigned char spi_send_read_byte(unsigned char byte);
void Delayms( unsigned t);
void Delayus( unsigned t);
void Delaytus( unsigned t);
// Constants
#define DESIRED_BAUDRATE (19200) // The desired BaudRate for RS232 communication w/ UART
// Main Function
int main(void)
{
// initialize onboard LEDs, IO pins, UART2, SPI1, set up nRF24L01+ as RX
Initialize();
char RS232_Out_Buffer[64]; // buffer for printing data to the screen via UART
unsigned char data; //register to hold letter sent and received
while(1)
{
nrf24l01_irq_clear_all(); //clear all interrupts in the 24L01
nrf24l01_set_as_rx(true); // force 24L01 to be a receiver (this is a double-check)
// is the 24L01 activated?
if (nrf24l01_irq_pin_active()) {
mLED_1_On();
} else {
mLED_1_Off();
}
// is the 24L01 receiving data?
if (nrf24l01_irq_rx_dr_active()) {
mLED_2_On();
} else {
mLED_2_Off();
}
//check to see if the data has been received. if so, get the data
if((nrf24l01_irq_pin_active() && nrf24l01_irq_rx_dr_active()))
{
mLED_3_On();
nrf24l01_read_rx_payload(&data, 1); //get the payload into data
sprintf(RS232_Out_Buffer, "\r\nrec data = %d\r\n", data); // show the data
putsUART2(RS232_Out_Buffer);
Delayms(2000);
} else { // otherwise, show that chip is still listening
putsUART2("...\r");
}
// toggle onboard LED 3 to indicate loop iterating
mLED_3_Off();
Delayms(10);
}
}
// Initialize all initialize functions (function descriptions to follow)
void Initialize(void) {
// initialize peripheral bus clock to SYS_FREQ (80 MHz)
int pbClk;
pbClk = SYSTEMConfigPerformance(SYS_FREQ);
// initialize UART
initUART2(pbClk);
// initialize input/output pins
InitializeIO();
// initialize the SPI channel 1 as master, no frame mode
SpiInitDevice(1, 1, 0, 0);
//initialize 24L01 to debug configuration as receiver, 1 byte data size, and auto-acknowledge mode disabled
nrf24l01_initialize_debug(true, 1, false);
// initialize all onboard LEDs on NU32
mInitAllLEDs();
// if program initialized correctly, indicate on PC & onboard LEDs
putsUART2("\r\n***** System Initialized *****\r\n");
mLED_0_On();
}
// initialize IO pins
void InitializeIO(void) {
TRISBbits.TRISB0 = 1; // set IRQ pin as input
TRISC = 0xFFF9; // make CSN, CE digital outputs
PORTC = 0x0004; // set CSN bit active
}
// initialize UART2
void initUART2(int pbClk)
{
#define config1 UART_EN | UART_IDLE_CON | UART_RX_TX | UART_DIS_WAKE | UART_DIS_LOOPBACK | UART_DIS_ABAUD | UART_NO_PAR_8BIT | UART_1STOPBIT | UART_IRDA_DIS | UART_DIS_BCLK_CTS_RTS| UART_NORMAL_RX | UART_BRGH_SIXTEEN
#define config2 UART_TX_PIN_LOW | UART_RX_ENABLE | UART_TX_ENABLE | UART_INT_TX | UART_INT_RX_CHAR | UART_ADR_DETECT_DIS | UART_RX_OVERRUN_CLEAR
OpenUART2( config1, config2, pbClk/16/DESIRED_BAUDRATE-1); // calculate actual BAUD generate value.
ConfigIntUART2(UART_INT_PR2 | UART_RX_INT_EN);
}
// initialize SPI
void SpiInitDevice(int chn, int isMaster, int frmEn, int frmMaster)
{
unsigned int config = SPI_CON_MODE16|SPI_CON_SMP|SPI_CON_ON; // SPI configuration word
if(isMaster)
{
config|=SPI_CON_MSTEN;
}
if(frmEn)
{
config|=SPI_CON_FRMEN;
if(!frmMaster)
{
config|=SPI_CON_FRMSYNC;
}
}
SpiChnOpen(chn, config, 4); // divide fpb by 4, configure the I/O ports. Not using SS in this example
}
// ******************************************************
/*
Function: spi_send_read_byte
Inputs: unsigned char byte
Outputs: unsigned short rxData
This function is required by the 24L01 header file.
It takes the inputted byte, sends it over the chosen
SPI channel, then waits to retreive data back.
*/
// ******************************************************
unsigned char spi_send_read_byte(unsigned char byte) {
unsigned short txData, rxData; // transmit, receive characters
int chn = 1; // SPI channel to use (1 or 2)
txData = byte; // take inputted byte and store into txData
SpiChnPutC(chn, txData); // send data
rxData = SpiChnGetC(chn); // retreive over channel chn the received data into rxData
return rxData;
}
// ******************************************************
/*
Functions: Delayms, Delayus
Inputs: unsigned t
Outputs: none
These functions are required by the 24L01 header file.
They take an input of t (ms, us) and delay the
program.
*/
// ******************************************************
void Delayms( unsigned t) {
// This uses Timer 1, can be changed to another timer. Assumes FPB = SYS_FREQ
OpenTimer1(T1_ON | T1_PS_1_256, 0xFFFF);
while (t--)
{ // t x 1ms loop
WriteTimer1(0);
while (ReadTimer1() < SYS_FREQ/256/1000);
}
CloseTimer1();
} // Delayms
void Delayus( unsigned t) {
OpenTimer1(T1_ON | T1_PS_1_256, 0xFFFF);
while (t--)
{ // t x 1ms loop
WriteTimer1(0);
while (ReadTimer1() < SYS_FREQ/256/1000000);
}
CloseTimer1();
} // Delayus
