PIC32MX: I2C Communication between PIC32s

Original Assignment

Do not erase this section!

Your assignment is to create code that allows two PIC32s to communicate via I2C.

Overview

Summarize briefly what the page is about.

Circuit

Code

(code description here)

Master Code

/*******************************************************
 * I2C_Master.c: Master code for I2C communication.	*
 * 	Both PICS use I2C1 module to send/ recieve data.*
 *	The master sends different values to a slave,   *
 *	which uses an interrupt to respond accordingly.	*
 *							*
 * Hardware: 2 PIC32MX460F512L PICs on NU32 boards	*
 *******************************************************
 * Thomas Peterson, James Rein, Eric West		*
 * ME333 Winter 2010					*
 * File Created: 	05-FEB-2010			*
 * Last Modified: 	14-FEB-2010			*
 *******************************************************/

#include "HardwareProfile.h"
#include <plib.h>

#define SYSCLK	(80000000)
#define PBCLK  (SYSCLK)
#pragma config FPBDIV = DIV_1				//Sets PBCLK to SYSCLK

#define Fsck	50000      					//Frequency of (I2C) serial clock
 
#define Nop() asm( "nop" )                 //No-operation; asm stands for assembly, using an assembly command in C.  Cool!

#define INPUT_A9       PORTAbits.RA9
#define INPUT_A10       PORTAbits.RA10


//function declaration for sending data and selecting slave address
void SendData(int,unsigned int);
void Delayms( unsigned t);

/*
This function is a delay function, causing the program to wait for approximately 4 * cnt cycles
1 cycle is 1/SYSCLK seconds.
*/
void i2c_wait(unsigned int cnt)
{
	while(--cnt)
	{
		Nop();
		Nop();
	}
}


/* Main function */
int main(void)
{
    // Configure the proper PB frequency and the number of wait states.
	SYSTEMConfigPerformance(SYS_FREQ);

	// Set all analog pins to be digital I/O
   	AD1PCFG = 0xFFFF;

	//Setup TRIS bits for switches and I2C pins
	TRISAbits.TRISA14=0;
	TRISAbits.TRISA15=0;

	//Initialize all of the LED pins
	mInitAllLEDs();
       mInitAllSwitches()

	unsigned char SlaveAddress;   //Slave address variable to tell the master where to send the data.  
                                     //Will be re-assigned for multiple slaves.

	//Enable I2C channel and set the baud rate to BRG_VAL)
	OpenI2C1( I2C_EN, BRG_VAL );

	int rcv;			//For received data

	//While loop to test LED functionality 
	while(1) {
		if (swProgram) {				//First button pressed
			while(swProgram) { Nop(); }	//Wait for release
			mLED_2_Toggle();			//Toggle LED2
			SendData(0xAA,0x40);  			//Sends hex data 0xAA to slave address 0x40
			rcv = RcvData(0x40);			//Receives data from address 0x40				
			Delayms(100);
		}
		if (swUser) {				//Second button pressed
			while(swUser) { Nop(); }
			mLED_1_Toggle();			//Toggle LED1
			SendData(0x23,0x40);    		//Sends hex data 0xAA to slave address 0x40
			rcv = RcvData(0x40);		        //Receives data from address 0x40			
			Delayms(100);		
		}
	}//while loop ending

	return 0;
}  //ending main 


/*****************************************************
 * RcvData(unsigned int address)		     *
 *					  	     *
 * Gets a byte of data from I2C slave device at      *
 *  ADDRESS.					     *
 *						     *
 * Returns: Received data			     *
 ****************************************************/
int RcvData(unsigned int address) {
	StartI2C1();				//Send line start condition
	IdleI2C1();			        //Wait to complete
	MasterWriteI2C1((address << 1) | 1);	//Write out slave address OR 1 (read command)
	IdleI2C1();				//Wait to complete
	int rcv = MasterReadI2C1();		//Read in a value
	StopI2C1();				//Send line stop condition
	IdleI2C1();				//Wait co complete
	return rcv;				//Return read value
}



/***************************************************
 * SendData(int data, unsigned int address)        *
 *						    *
 * Sends a byte of data (DATA) over the I2C line   *
 *	to I2C address ADDRESS			    *
 *						    *
 * Returns: nothing				    *
 ***************************************************/
void SendData (int data, unsigned int address){
	StartI2C1();	        //Send the Start Bit
	IdleI2C1();		//Wait to complete

	MasterWriteI2C1((address << 1) | 0);  //Sends the slave address over the I2C line.  This must happen first so the 
                                             //proper slave is selected to receive data.
	IdleI2C1();	        //Wait to complete

	MasterWriteI2C1(data);  //Sends data byte over I2C line
	IdleI2C1();		//Wait to complete

	StopI2C1();	        //Send the Stop condition
	IdleI2C1();	        //Wait to complete

} //end function



void Delayms( unsigned t)
// This uses Timer 1, can be changed to another timer. Assumes FPB = SYS_FREQ
{
    OpenTimer1(T1_ON | T1_PS_1_256, 0xFFFF);
    while (t--)
    {  // t x 1ms loop
        WriteTimer1(0);
        while (ReadTimer1() < SYS_FREQ/256/1000);
	}
	CloseTimer1();
} // Delayms

Slave Code

/***********************************************************************
 * PIC32 I2C Slave Code                
 ***********************************************************************/

#include "GenericTypeDefs.h"
#include "Compiler.h"
#include "HardwareProfile.h"
#include <plib.h>

#define SYSCLK	(80000000)
#define PBCLK  (SYSCLK)

#define Fsck	50000
#define BRG_VAL 	((PBCLK/2/Fsck)-2)

// this is the modules Slave Address
#define SLAVE_ADDRESS 0x40

// volatile variables to hold the switch and led states
volatile unsigned char dataRead = 0;

///////////////////////////////////////////////////////////////////
//
//	InitI2C
//
// 	Perform initialisation of the I2C module to operate as a slave
//
///////////////////////////////////////////////////////////////////
void InitI2C(void)
{
	unsigned char temp;
	
	// Enable the I2C module with clock stretching enabled
	OpenI2C1(I2C_ON | I2C_7BIT_ADD | I2C_STR_EN, BRG_VAL);
	
	// set the address of the slave module, address matching is with bits
	// 7:1 of the message compared with bits 6:0 of the ADD SFR so we
	// need to shift the desired address 1 bit. 
	I2C1ADD = SLAVE_ADDRESS; // >> 1;
	I2C1MSK = 0;
	
	// configure the interrupt priority for the I2C peripheral
	mI2C1SetIntPriority(I2C_INT_PRI_3 | I2C_INT_SLAVE);

	// clear pending interrupts and enable I2C interrupts
	mI2C1SClearIntFlag();
	EnableIntSI2C1;
}

///////////////////////////////////////////////////////////////////
//
//	main routine
// 
//	This code example demonstrates using the PIC32 as an I2C slave
//	
//
///////////////////////////////////////////////////////////////////
int main (void)
{
	// set for 80MHz operation
	SYSTEMConfigPerformance(SYSCLK);
	// set the Pbus to be 40000000
	mOSCSetPBDIV(OSC_PB_DIV_2);
	// disable the JTAG port
	mJTAGPortEnable(0);
	// enable interrupts
	INTEnableSystemMultiVectoredInt();
	
	InitI2C();
	mInitAllLEDs();

	// main loop
	while (1) {
		/* If global variable "dataRead" is set high during interrupt, turn on all LEDs */
		if (dataRead == 0xAA)
		{
			mLED_0_On();
			mLED_1_On();
			mLED_2_On();			
			mLED_3_On();			
			
		}
	}
}

///////////////////////////////////////////////////////////////////
//
// Slave I2C interrupt handler
// This handler is called when a qualifying I2C events occurs
// this means that as well as Slave events 
// Master and Bus Collision events will also trigger this handler.
//
///////////////////////////////////////////////////////////////////
void __ISR(_I2C_1_VECTOR, ipl3) _SlaveI2CHandler(void)
{
	mLED_1_On();
	unsigned char temp;
	static unsigned int dIndex;
	
	// check for MASTER and Bus events and respond accordingly
	if (IFS0bits.I2C1MIF == 1) {
		mI2C1MClearIntFlag();
		return;		
	}
	if (IFS0bits.I2C1BIF == 1) {
		mI2C1BClearIntFlag();
		return;
	}
	mLED_1_Off();
	mLED_2_On();
	
	// handle the incoming message
	if ((I2C1STATbits.R_W == 0) && (I2C1STATbits.D_A == 0)) {
		// R/W bit = 0 --> indicates data transfer is input to slave
		// D/A bit = 0 --> indicates last byte was address  
		
		// reset any state variables needed by a message sequence	
		// perform a dummy read of the address
		temp = SlaveReadI2C1();
		
		mLED_3_On();
		mLED_2_Off();
		// release the clock to restart I2C
		I2C1CONbits.SCLREL = 1; // release the clock

	} else if ((I2C1STATbits.R_W == 0) && (I2C1STATbits.D_A == 1)) {
		// R/W bit = 0 --> indicates data transfer is input to slave
		// D/A bit = 1 --> indicates last byte was data
		
		mLED_3_On();
		mLED_2_On();
		// writing data to our module, just store it in adcSample
		dataRead = SlaveReadI2C1();
		
		// release the clock to restart I2C
		I2C1CONbits.SCLREL = 1; // release clock stretch bit

	} else if ((I2C1STATbits.R_W == 1) && (I2C1STATbits.D_A == 0)) {
		// R/W bit = 1 --> indicates data transfer is output from slave
		// D/A bit = 1 --> indicates last byte was address
		mLED_0_On();
		mLED_2_Off();
		// read of the slave device, read the address 
		temp = SlaveReadI2C1();
		dIndex = 0;
		SlaveWriteI2C1(dataRead);
	} else if ((I2C1STATbits.R_W == 1) && (I2C1STATbits.D_A == 1)) {
		// R/W bit = 1 --> indicates data transfer is input to slave
		// D/A bit = 1 --> indicates last byte was data
		mLED_0_On();
		mLED_2_On();
		
		// output the data until the MASTER terminates the
		// transfer with a NACK, continuing reads return 0
		if (dIndex == 0) {
			SlaveWriteI2C1(dataRead);
			dIndex++;
		} else
			SlaveWriteI2C1(0);
	}
	
	// finally clear the slave interrupt flag
	mI2C1SClearIntFlag();		
}