Machine Vision Localization System

From Mech
Jump to navigationJump to search

Overview

This is a machine vision system that tracks multiple targets and can send out the positions via the serial port. It was developed specifically for the Swarm Robotics project, but can be adapted for other uses. It is based upon the Indoor_Localization_System, but has several enhancements and bug fixes. Refer to Indoor_Localization_System for a basic overview of the setup of the system and the workings of the patter identification algorithm.

Major Enhancements/Changes

  • The system will now mark the targets with an overlay and display coordinate data onscreen.
  • The serial output is now formatted for the XBee radio using the XBee's API mode with escape characters.
  • The calibration routine has been improved, and only needs to be performed once.
  • A command interface for sending out commands via the serial port has been added.
  • The system will discard targets too close to the edge of the camera frame to prevent misidentification due to clipping.
  • The origin of the world coordinate is now in the middle, not the lower left corner.
  • The GUI displaying the camera frames is now full sized instead of a thumbnail. However, if your monitor isn't big enough, you can resize them.

Major Bug Fixes

  • Two major memory leaks fixed.
  • Calibration matricies are now calculated correctly.
  • File handling bug that causes an off-by-one error in LoadTargetData() fixed.

Camera Calibration Routine

The camera calibration routine used is explained in the document Image_Formation_and Camera_Calibration.pdf by Professor Ying Wu.

Target Patterns

The target patterns and preprocessor can be downloaded at Indoor_Localization_System#Pre-processing_program_source_with_final_patterns:.

Operation

Setting up the Cameras

Camera setup.png


The cameras should be set up according to Indoor_Localization_System with one caveat: targets at the edge of the camera frame will now be discarded. This prevents misidentification of patterns if one or more dots in the pattern fall off the screen, but it also means that there must be enough overlap that when the target is in the dead-zone of one camera, it is picked up by another camera.

Targets found in the margin are discarded.


The frames must overlap; overlap by the width of one target to ensure that it will never be discarded by both cameras.


Starting the Program

  1. When you first run the program, it will open up a console window and ask you to enter a COM port number. This is the number of the serial port that will be used to send out data. Enter the number, and press Enter. (e.g. Enter COM number: 4<enter>)
  2. The program should now connect to the cameras, and will open two new windows: one with numbered quadrants (the GUI window), and one displaying the view of one of the cameras. Use you mouse to click on the quadrant that corresponds to the camera view. Repeat until all four cameras have been matched to the quadrants.
  3. Make sure the GUI window is selected, and press Enter.
  4. Go back to the console window, and you should now see a message asking you if you want to recalibrate your cameras. Press y for yes and n for no, then press Enter. To recalibrate your cameras, see the calibration section.
  5. The GUI window should now show a thresholded image, and the console will display how many dots the camera sees. Adjust the thresholding parameters (+ and - for black/white, z and x for area) until you are satisfied with the thresholded image.
  6. Make sure the GUI window is selected, then hit Enter.
  7. Remove any calibration patterns, and hit Enter. The program should now be running.

Pausing

Hit 'p' to pause the program, and hit 'p' again to resume.

Using the Command Console

To enter the command mode, hit 'c'. When in the command mode, the main loop is not running; the command mode must be exited to resume. Type 'exit' to exit the command mode and resume the main loop.

Enter commands in the following syntax: <command name> <target ID> <parameter 1> <parameter 2> ... <parameter N>

Exiting the Program

Press ESC to quit the program.

Calibration

Twenty-five points are used to calibrate the cameras.