Rotary Encoder

From Mech
(Difference between revisions)
Jump to: navigation, search
 
(13 intermediate revisions by 12 users not shown)
Line 16: Line 16:
 
are composed of a glass or plastic slotted disk. As
 
are composed of a glass or plastic slotted disk. As
 
radial lines in each track interrupt the beam between a
 
radial lines in each track interrupt the beam between a
photoemitter-detector pair (or [[Optointerrupter]]), digital pulses are produced.
+
photoemitter-detector pair (or [[Optointerrupter]]), digital pulses are produced.  Below is a figure of an encoder with a spinning codewheel and a stationary mask.  This stationary mask is usually not used.
  
 
<br clear="all">
 
<br clear="all">
Line 308: Line 308:
 
binary bit is the exlcusive OR (XOR) combination of adjacent gray
 
binary bit is the exlcusive OR (XOR) combination of adjacent gray
 
code bits.
 
code bits.
293835705943398248937778
 
<u style="display:none;"> The  not department outpatient [http://www.svetadura.familyplanit.com/getfile.aspx?wfc=59776d43-6e49-4184-8aa8-f906c86a7b77&f=paxil-side-effects.html  paxil side effects]. [ ]  samples.</u>
 
<u style="display:none;"> On the [http://www.tetkizlo.familyplanit.com/getfile.aspx?wfc=a5b20479-4875-4ae8-8ebb-14678da8de69&f=cialis\tadalafil.html  tadalafil] options through unless  fall 2005 april in. [http://www.tetkizlo.familyplanit.com/getfile.aspx?wfc=a5b20479-4875-4ae8-8ebb-14678da8de69&f=cialis\generic-cialis.html  generic cialis] while  process brand-name.</u>
 
<u style="display:none;"> And [http://www.tetkizlo.familyplanit.com/getfile.aspx?wfc=a5b20479-4875-4ae8-8ebb-14678da8de69&f=sildenafil-citrate.html  sildenafil citrate] . From [http://www.tetkizlo.familyplanit.com/getfile.aspx?wfc=a5b20479-4875-4ae8-8ebb-14678da8de69&f=generic-cialis-online.html  generic cialis online] who  concerns paps acetate
 
hydrocortisone.</u>
 
  
 
<h4>Incremental encoder</h4>
 
<h4>Incremental encoder</h4>
Line 356: Line 351:
 
or B, it would be impossible to determine the direction of
 
or B, it would be impossible to determine the direction of
 
rotation. Furthermore, shaft jitter around an edge transition in
 
rotation. Furthermore, shaft jitter around an edge transition in
the single signal woudl result in erroneous pulses..
+
the single signal would result in erroneous pulses.
  
 
[[image:quadrature.jpg|500px]]
 
[[image:quadrature.jpg|500px]]

Latest revision as of 13:12, 2 February 2010

Encoder disk.jpg

A digital optical encoder is a device that converts motion into a sequence of digital pulses. By counting a single bit or by decoding a set of bits, the pulses can be converted to relative or absolute position measurements. Encoders have both linear and rotary configurations, but the most common type is rotary. Rotary encoders are manufactured in two basic forms: 1) the absolute encoder where a unique digital word corresponds to each rotational position of the shaft, and 2) the incremental encoder, which produces digital pulses as the shaft rotates, allowing measurement of relative position of shaft. Most rotary encoders are composed of a glass or plastic slotted disk. As radial lines in each track interrupt the beam between a photoemitter-detector pair (or Optointerrupter), digital pulses are produced. Below is a figure of an encoder with a spinning codewheel and a stationary mask. This stationary mask is usually not used.


Encoder diagram.png

Absolute encoder

The optical disk of the absolute encoder is designed to produce a digital word that distinguishes N distinct positions of the shaft. For example, if there are 8 tracks, the encoder is capable of producing 256 distinct positions or an angular resolution of 1.406 (360/256) degrees. The most common types of numerical encoding used in the absolute encoder are gray and binary codes. To illustrate the acion of an absolute encoder, the gray code and natural binary code dsisk track patterns for a simple 4-track (4-bit) encoder are illustrated in Fig 2 and 3. The linear patterns and associated timing diagrams are what the photodetectors sense as the code disk circular tracks rotate with the shaft. The output bit codes for both coding schemes are listed in Table 1.

Gray.jpg Binary.jpg


Decimal code

Rotation range (deg.)

Binary code

Gray code

0

0-22.5

0000

0000

1

22.5-45

0001

0001

2

45-67.5

0010

0011

3

67.5-90

0011

0010

4

90-112.5

0100

0110

5

112.5-135

0101

0111

6

135-157.5

0110

0101

7

15.75-180

0111

0100

8

180-202.5

1000

1100

9

202.5-225

1001

1101

10

225-247.5

1010

1111

11

247.5-270

1011

1110

12

270-292.5

1100

1010

13

292.5-315

1101

1011

14

315-337.5

1110

1001

15

337.5-360

1111

1000


Table 1. 4-Bit gray and natural binary codes

File:Conv.jpg
Fig 4. Gray code to binary code conversion

The gray code is designed so that only one track (one bit) will change state for each count transition, unlike the binary code where multiple tracks (bits) change at certain count transitions. This effect can be seen clearly in Table 1. For the gray code, the uncertainty during a transition is only one count, unlike with the binary code, where the uncertainty could be multiple counts.

Since the gray code provides data with the least uncertainty but the natural binary code is the preferred choice for direct interface to computers and other digital devices, a circuit to convert from gray to binary code is desirable. Figure 4 shows a simple circuit that utilizes exclusive OR gates (XOR) to perform this function.For a gray code to binary code conversion of any number of bits N, the most signficant bits (MSB) of the binary and gray code are always identical, and for each other bit, the binary bit is the exlcusive OR (XOR) combination of adjacent gray code bits.

Incremental encoder

Increment.jpg

The incremental encoder, sometimes called a relative encoder, is simpler in design than the absolute encoder. It consists of two tracks and two sensors whose outputs are called channels A and B. As the shaft rotates, pulse trains occur on these channels at a frequency proportional to the shaft speed, and the phase relationship between the signals yields the direction of rotation. The code disk pattern and output signals A and B are illustrated in Figure 5. By counting the number of pulses and knowing the resolution of the disk, the angular motion can be measured. The A and B channels are used to determine the direction of rotation by assessing which channels "leads" the other. The signals from the two channels are a 1/4 cycle out of phase with each other and are known as quadrature signals. Often a third output channel, called INDEX, yields one pulse per revolution, which is useful in counting full revolutions. It is also useful as a reference to define a home base or zero position.

Figure 5 illustrates two separate tracks for the A and B channels, but a more common configuration uses a single track with the A and B sensors offset a 1/4 cycle on the track to yield the same signal pattern. A single-track code disk is simpler and cheaper to manufacture.

The quadrature signals A and B can be decoded to yield the direction of rotation as hown in Figure 6. Decoding transitions of A and B by using sequential logic circuits in different ways can provide three different resolutions of the output pulses: 1X, 2X, 4X. 1X resolution only provides a single pulse for each cycle in one of the signals A or B, 4X resolution provides a pulse at every edge transition in the two signals A and B providing four times the 1X resolution. The direction of rotation(clockwise or counter-clockwise) is determined by the level of one signal during an edge transition of the second signal. For example, in the 1X mode, A=\downarrow with B =1 implies a clockwise pulse, and B=\downarrow with A=1 implies a counter-clockwise pulse. If we only had a single output channel A or B, it would be impossible to determine the direction of rotation. Furthermore, shaft jitter around an edge transition in the single signal would result in erroneous pulses.

Quadrature.jpg

Encoder parts.png

Connecting an Encoder to the PC/104 Stack

To connect an encoder to the PC/104 stack, you will have to create a suitable ribbon cable connector. The connector that came with the encoder will most likely not match the correct pinout to attach. Consult the PC104 I/O page to see how to connect the encoder.

Datasheets

Datasheet for the Maxon Tacho 103935 encoder: Media:maxon_tacho_103935_encoder.pdf

References

Introduction to Mechatronics and Measurement Systems, Histand & Alciatore, 1999 McGraw Hill

Personal tools