Difference between revisions of "RGB Swarm Robot Project Documentation"

From Mech
Jump to navigationJump to search
Line 413: Line 413:
----
----


===='''Additional Machine Vision System Modifications'''====
===='''Additional Considerations'''====


While there do not need to be any additional changes to the set up of the machine vision localization system, there may be additional considerations for further development. One such consideration is the 'background', or floor material, of the setup. With the modified machine vision code, light intensity is what is picked up and filtered by the system, thus rendering the LEDs from the e-pucks to be the only tracked objects. However, with more advanced set ups, such as one featuring light that is projected onto the background, this may present a problem with the machine vision system picking up reflected light. More testing has to be done with modifying the machine vision system threshold to see if there is an ideal threshold to accommodate this setup. Another option may be to use a non-reflective or matte surface for the background.
While there do not need to be any additional changes to the set up of the machine vision localization system, there may be additional considerations for further development. One such consideration is the 'background', or floor material, of the setup. With the modified machine vision code, light intensity is what is picked up and filtered by the system, thus rendering the LEDs from the e-pucks to be the only tracked objects. However, with more advanced set ups, such as one featuring light that is projected onto the background, this may present a problem with the machine vision system picking up reflected light. More testing has to be done with modifying the machine vision system threshold to see if there is an ideal threshold to accommodate this setup. Another option may be to use a non-reflective or matte surface for the background.

Revision as of 10:43, 14 July 2009

Overview

This project consists of two main parts; the improvement of e-puck hardware and the theoretical research on estimating the environment using data collected by the sensor. The e-pucks are improved to have a new version of XBee interface extension board which contains a color sensor to collect data, and have a new LED pattern board at the top of it. By designing this new LED pattern board, each black dot pattern of e-pucks, which has been used by the machine vision system, was replaced by the LED, and the machine vision system is improved in a way to recognize each robot by its LED lights, not by the black dots. Theoretical part introduces several research papers and their main theme. It focuses on two major ideas: how the environmental estimation, or measurement, models are formulated and presented, and how errors are estimated and possibly reduced.

Hardware

XBee Interface Extension Board

Previous Version

XBee interface extenstion board v1.gif

The previous version of XBee interface Extension Board, designed by Michael Hwang. Its configuration is shown in the figure on the left. This version of XBee Board does not contain a color sensor in it. Details about this version of XBee Interface Extension Board can be found here:http://hades.mech.northwestern.edu/wiki/index.php/Swarm_Robot_Project_Documentation#Current_Version



Current Version

XBee interface extenstion board v2.gif

The upgraded version of XBee Interface Extension Board. It is designed by Michael Hwang. This version has a color sensor circuit built in. The details of the color sensor circuit can be found in the color sensor section below. The RTS flow control line on the XBee is connected to the sel3 line of the e-puck. Although the CTS line is not connected to the sel2 pin in this board design, it can be easily connected with a jumper.


This new version of XBee Interface Extension Board design was actually built and implemented on the e-puck # 3. In order to see if there is any working problem in this board design, it is first tested with the other e-puck which uses the previous XBee Boards.


The e-puck # 3 upgraded with the new XBee board did not show any problem in communicating with other e-pucks. According to the goal defined, all e-pucks, including e-puck # 3, locate themselves to the desired location.



Color Sensor Circuit

Color sensor circuit diagram v1 R.gif


For this color sensor circuit, a high-impedance op-amp, LMC6484, is used to amplify signals from three photodiodes (for red, green, and blue) of the color sensor. This amplified ouputs are sent to the ADC channels which had been used as the X,Y, and Z axis accelerometers. A 10k potentiometer controls the ratio of amplification.

Color sensor circuit diagram v1 G.gif

As you may noticed from the circuit diagram on the left, when each photodiode received a light, the certain amount of current start to flow through the photodiodes and generates a voltage across R1 = 680K. Each photodiode is designed to detect the certain range of wavelength of the light, and the amount of current flowing through the photodiodes is determined according to the amount of the corresponding light to each photodiode.


Color sensor circuit diagram v1 B.gif


The op-amp, LMC6484, takes the voltage generated across R1 as an input signal to amplify, and amplifies it as much as the ratio we define using the 10K potentiometer. The corresponding equation is following.


|Vo| = |Vi*(R2/Rpot)|


Rpot = resistance of the potentiometer (shown in the diagram)

R2 = 100K (shown in the diagram)

Vi = voltage across R1 = 680K, which the op-amp takes as an input

Vo = output signal amplified from the op-amp


The ratio of amplification is approximately 20. Thus, the input voltage, Vi, is amplified to be 20Vi, which is Vo. As mentioned above, this ratio can be adjusted properly by controling the resistance of the potentiometer.


As shown in the circuit diagram on the left, the siganl from the red photodiode goes into the pin #5, and the amplified signal is sent out through the pin # 7. Similarly, the signal from the green photodiode goes into the pin #3 and it is sent out from pin # 1 while the signal from the blue photodiode goes into the pin #12, and it is sent out from pin #7.


Output Pins

  • Pin #7 - Amplified Red photodiode signal
  • Pin #1 - Amplified Green photodiode signal
  • Pin #14 - Amplified Blue photodiode signal

Parts used

Parts used in both the previous version and the new version of XBee Interface Extension Board

  • 2x 10 pos. 2 mm pitch socket (Digikey S5751-10-ND)
  • LE-33 low dropout voltage regulator (Digikey 497-4258-1-ND)
  • 2.2uF tantalum capacitor (Digikey 399-3536-ND)
  • 2x Samtec BTE-020-02-L-D-A (Order directly from Samtec)
  • 0.1"header pins for RTS and CTS pins (you can also use wire for a permanent connection)
  • 2x 0.1" jumpers for connecting RTS and CTS pins if you used header pins(Digikey S9000-ND)

Additional parts for new version of XBee Interface Extension Board

  • 3x 100K resistors
  • 3x 680K resistors
  • 3x 10K potentiometer
  • 3x 5pF capacitor
  • 1x RGB color sensor (Order directly from HAMAMATSU, part#:s9032-02, Datasheet)
  • 1x High impedence op-amp LMC6484

Future modification

As mentioned in the overview, the black dot patterns of e-pucks are replaced with new LED patterns by implementing LED pattern board at the top of each e-puck. Thus, in order for the color sensor to collect data properly, it is necessary to move the color sensor from the XBee Interface Extension Board to the LED pattern board so that nothing will block the color sensor. All other components for the color sensor circuit remains in the XBee Interface Extension Board and only the color sensor will be place in the LED pattern board. We can use a jumper to connect the color sensor placed at the LED pattern board to the color sensor circuit place in the XBee Interface Extension Board. The datails of this LED pattern Board will be presented at the section below.


LED Pattern Board

LED pattern board.gif

This new LED pattern board is introduced for the Swarm Robot Project. Currently, the unique black dot pattern of each e-puck was used for the machine vision system to recognize each e-puck. However, this black dot pattern requires a white background in order for the machine vision system to recognize e-pucks. The new LED pattern board uses LEDs with the proper brightness, instead of the black dot pattern. By doing so, the machine vision system can now recoginize e-pucks on any background. The reason why this LED pattern is recognized on any background will be presented briefly in the Code section below. In addition, in order to apply this LED pattern to the machine vision system, we made a modification in code. This modification will also be presented in the Code Section below. The PCB file can be downloaded here: Media:LED_Pattern_Board.pcb



LED Pattern Board Design

This LED Pattern Board is created using Traxmaker. This LED Board design can be downloaded here: Although we replaced the black dots with LEDs, we maintain each pattern of dots. The horizontal distance and the vertical distance between the two adjacent LEDs are both 0.8 inch. In order to reduce power consumption of the e-puck battery, we implement a seperate pair of AAA batteries to supply power to the LEDs. This LED board can be turned on and off by the switch. The milicandela rating of the LEDs used is 4850 mcd. In addition, this LED has diffused lens style. The reason to choose this LED is that it has a proper brightness and power consumption, and it is diffused so that the machine vision system can capture this LED in any places.The resistor used are 68.7 ohm.

As mentioned in the XBee Interface Extension Board section, the color sensor has to be moved to this LED pattern board from the XBee Interface Extension Board so that nothing blocks the sensor. Thus, as you can see in the Figure on the left, the color sensor is place at the front, and each photodiode is connected to the 10 pin header. This header connects the color sensor on the LED pattern board to the remaining part of color sensor circuit on the XBee Interface Extension Board.


Parts used

  • 3x LED (Digikey 516-1697-ND): Some e-pucks require 4 LEDs since they have a pattern composed of 4 dots
  • 3x 68.7 ohm resistors : Some e-pucks require 4 resistors since they have 4 LEDs
  • 2x AAA Battery Holder (Digikey 2466K-ND)
  • 1x Switch (Digikey CKN1068-ND)
  • 1x RGB color sensor (Order directly from HAMAMATSU, part#:s9032-02)
  • 1x 10 pos. 2 mm pitch socket (Digikey S5751-10-ND)

Test With Vision System

The epuck with the LED pattern board was tested with the machine vision system. As a result, the machine vision system does not show any problem, and it can capture the e-puck located in any places. In addition , the vision system captures the e-puck as it moves. The recoginition of the machine vision system was very stable because the vision system never loses the e-puck.


Next Step

The LED Pattern Board design above needs to be modified in the following parts.

  • The hole size for the LEDs has to increase so that it can accomodate the standoff of the LED chosen.
  • The hole size for the switch has to increase so that the switch can be completely inserted through the hole.
  • Currently, 10 pos 2mm pitch socket is used to connect the color sensor to the circuit using wires. Instead, the proper header for the color sensor has to be found to connect the color sensor and the circuit more conveniently.

Light Inteference Experiment

As mentioned above, the black dot patterns of e-pucks are replaced by the LEDs, and accordingly the color sensor is placed at the LED pattern board. Now, we have to consider the potential interference between the light from LEDs and the color sensor. Thus, the experiment on the LED light interference is performed.


Distance vs Signal

The first experiment is designed to see how much interference will be caused as the distance between the LED and the color sensor changes.


Experimental Setup

1. A white LED is used in this experiment because the white LED will cover the entire wavelengh ranges of the visible light. The experiment with the white LED can yield a general result, while the experiement with the colored LEDs will yield more specific result focused on the interference between the certain photodiode and the certain color.

  • LED: 18950 mcd, digikey part number: C503B-WAN-CABBB151-ND

2. The experiment was performed under the two conditions; with the ambient light and without the ambient light.

3. The LED and the color sensor were placed at the same plane, and both are facing upward.

4. Distance between the color sensor and the LED is increased by 0.25 inch each time from 1 inch to 2.5 inch.

5. The amplified output, Vo as shown in the circuit diagram above, of each photodiode is measured.


Experiment Result


1. With the ambient light

Distance vs output with room light.gif
  • Unit: Volt, V
Distance vs Amplified Output
Distance R G B
No LED 1 1.4 0.469
1 inch 1.259 1.716 0.832
1.25 inch 1.185 1.619 0.757
1.5 inch 1.135 1.529 0.669
1.75 inch 1.097 1.503 0.613
2 inch 1.086 1.481 0.589
2.25 inch 1.071 1.47 0.563
2.5 inch 1.06 1.453 0.546



2. Without the ambient light

Distance vs output without room light.jpg
  • Unit: Volt, V
Distance vs Amplified Output
Distance R G B
No LED 0.028 0.025 0.019
1 inch 0.244 0.221 0.223
1.25 inch 0.195 0.166 0.143
1.5 inch 0.162 0.123 0.097
1.75 inch 0.130 0.097 0.069
2 inch 0.102 0.077 0.054
2.25 inch 0.087 0.064 0.045
2.5 inch 0.073 0.056 0.039



Analysis

As you can see in the two graphs above, the color sensor is affected by the light from the LED. The color sensor is most affectd by the LED when the LED is closest to it. As the distance between the LED and the color sensor increases, the interference decreases. When the color sensor is most affected by the LED under the presence of the room light, the output increases upto 25.9%, 22.6%, and 43.6 % of the original output. As the LED is 2.5 inch away from the color sensor, the output becomes very close to the original value.

In this experiment, we see that the lights from LEDs can affect the color sensor. However, we used much brighter LED in this experiment than the ones we use in the LED pattern board. The brightness of the LED used in the experiment is 4 times larger than the ones in the LED pattern board. Thus, more experiment with the LEDs used in the LED pattern board is required.


Angle vs Signal

The second experiment is designed to see how much interference will be caused as the angle between LED and color sensor changes. Different from the first experiment, Vi, the voltage before amplified, is mesured since amplified output, Vo, easily reaches to the maximum.


Experimental Setup

1. A white LED is used again in this experiment with the same reason above for the first experiment.

  • LED: 18950 mcd, digikey part number: C503B-WAN-CABBB151-ND

2. The experiment was performed under the two conditions; with the ambient light and without the ambient light.

3. In this experiment, the distance between LED and color sensor is kept constant, 1 inch.

4. Angle between LED and color sensor is increased by 15º each time from 0º to 90º.

When the angle is 0º, the LED and the color sensor is placed at the same horizontal plane. The LED is facing toward the color sensor(this means that the LED is parallel to the horizontal plane with its head facing the LED placed on the same horizontal plane), and the color sensor is facing upward. We increased the angle by 15º each time, while the LED shines light on the color sensor directly. When the angle is 90º, the LED is right above the color sensor, facing the color sensor directly. This means that the LED and the color sensor are now on the same vertical line, and the LED is facing downward.


5. The voltage before amplified, Vi as shown in the circuit diagram above, of each photodiode is measured.

  • The reason to measure the volatage before amplified is that the output becomes too large after amplified.

Experiment Result


1. With the ambient light

Angle vs output with room light.gif
  • Unit: Volt, V
Angle vs Voltage Before Amplified
Angle R G B
0.437 0.425 0.404
15º 0.475 0.470 0.451
30º 0.490 0.491 0.501
45º 0.505 0.506 0.520
60º 0.484 0.468 0.484
75º 0.457 0.453 0.440
90º 0.439 0.430 0.408



2. Without the ambient light

Angle vs output without room light.jpg
  • Unit: Volt, V
Angle vs Voltage Before Amplified
Angle R G B
0.446 0.436 0.416
15º 0.454 0.491 0.461
30º 0.493 0.505 0.480
45º 0.512 0.521 0.520
60º 0.498 0.486 0.491
75º 0.498 0.492 0.487
90º 0.485 0.479 0.515



Analysis

As the first experiment, two graph above shows that the color sensor is affected by the light from the LED. The color sensor is most affectd by the LED when the angle between two is 45º. The inteference increases as the angle goes to 45º, and reaches to the peak at 45º. Then it decreases as the angle goes to 90º. When the color sensor is most affected by the LED under the presence of the room light, the output increases upto 15.6%, 19.1%, and 28.7% of Vi. As angle becomes 90º, the output becomes very close to the value at the angle of 0º. The reason why the interference is reduced as the angle reaches 90º is that the ambient light presented are blocked by the LED board. When we perform this experiment, the LEDs are implemented on the LED plane. This LED plane blocks the light and make a shadow on the color sensor. Thus, the amount of light that the color sensor receives decreases. That is why the output becomes close to its original value while the angle increases.



Machine Vision Localization System Modification

The machine vision localization system takes the real (color) image from the four cameras, and converts it into a grey-scale image. Then, using a threshold set in the machine vision code, the grey-scaled image is divided into black and white, and this black and white image is presented on the machine vision system computer screen. With the current set-up, the white background on the floor is presented as black, and black dot patterns on e-pucks are presented as white patterns. The system recognizes theses white dot patterns and identify e-pucks.

However, there is a problem with using black dot patterns to identify e-pucks. Since the machine vision system and code use a set threshold to divide the grey image into black and white, black dot patterns are affected by the background color due to lack of contrast. For instance, if the background is black, the system would not capture the pattern properly. In addition, other problems arise from dirt and debris tracked onto the white surface of the floor.

A solution is to substitute the black dots with LEDs placed atop the e-pucks, allowing the machine vision system to capture the identification pattern clearly regardless of background color and condition. By adjusting the threshold set in the machine vision code, the system will rely on the contrast of light intensity, minimizing the interference of the operating environment whose light intensity is which is naturally weaker than LEDs'.


Compatibility Problem of Original Code with LEDs

With the original code implementation, the system could not recognize LED patterns on e-puck; it only recognizes white patterns on the screen, which are black patterns in the reality. This problem can be simply fixed with modifying code to make the system capture LED patterns and present them as white patterns on the screen. The change of program will be shown in the next section. With this change, the system now makes LED patterns white dot patterns on the screen, so it can recognize them and identify e-pucks.


Change from Original Code

In main.cpp in VisionTracking project, the code has been changed in

Line 48:

cvThreshold(greyImage[camerai], thresholdedImage[camerai], threshold, 255, CV_THRESH_BINARY_INV);

to

cvThreshold(greyImage[camerai], thresholdedImage[camerai], threshold, 255, CV_THRESH_BINARY);

and

Line 735:

cvThreshold(grey, thresholded_image, threshold, 255, CV_THRESH_BINARY_INV);

to

cvThreshold(grey, thresholded_image, threshold, 255, CV_THRESH_BINARY);

Also, in global_vars.h,

Line 65:

double threshold = 75;   //black/white threshold

to

double threshold = 200;   //black/white threshold

Result

As change CV_THRESH_BINARY_INV in both line 48 and 735 to CV_THRESH_BINARY and adjust the value of threshold from 75 to 200, the system now clearly presents LED patterns as white dot patterns on the screen, so it can identify e-pucks according to LED patterns.


Additional Threshold Experimentation

The threshold value of 200 is determined to be good enough for the test inside. With various conditions, however, the threshold value can, or should, be changed more properly. In addition, the results for different range of threshold under the same test condition is presented below:

Threshold range
Range Result
0 - 94 System cannot caputure LED patterns at all; whole screen is white.
95 - 170 System can recognize the pattern but it is unstable, since most of background becomes white.
171 - 252 System cleary captures and recognizes LED patterns.
253 System can recognize the pattern but it is unstable since pattern is too small; stronger intensity is required.
254 - 255 System cannot caputure LED patterns at all; whole screen is black.



Additional Considerations

While there do not need to be any additional changes to the set up of the machine vision localization system, there may be additional considerations for further development. One such consideration is the 'background', or floor material, of the setup. With the modified machine vision code, light intensity is what is picked up and filtered by the system, thus rendering the LEDs from the e-pucks to be the only tracked objects. However, with more advanced set ups, such as one featuring light that is projected onto the background, this may present a problem with the machine vision system picking up reflected light. More testing has to be done with modifying the machine vision system threshold to see if there is an ideal threshold to accommodate this setup. Another option may be to use a non-reflective or matte surface for the background.

Theoretical Research

Introduction

In this theoretical research part, we will introduce project related research papers and provide with a brief explanation for main ideas, algorithms, for papers. Major mathematical expressions, or equations, for each paper will be presented. Also, there will be link for original papers.


Bibliography Report

i. Distributed Kriged Kalman Filter for Spatial Estimation

Author: Jorge Cort´es

This paper considers robotic sensor networks performing spatially-distributed estimation tasks. A robotic sensor network takes successive point measurements, in an environment of interest, of a dynamic physical process model as a spatio-temporal random field. The paper introduces Distributed Kriged Kalman Filter for predictive inference of the random field and its gradient.

Physical process as spatio-temporal Gaussian random field Z:
Gaussian random field.gif
Mean: Mean.gif


Robotic network of n agents {p1, … , pn} in Rd:
Robotic Network.gif
Number of network agent n is a priori known to everybody


Spatial Prediction:
Spatial Prediction.gif
For spatial prediction, simple kriging and parameter estimation are combined. Similar procedure can be carried out for sequential estimation, when measurements are taken successively.

Link for this paper: http://tintoretto.ucsd.edu/jorge/publications/data/2007_Co-tac.pdf

ii. Data Assimilation via Error Subspace Statistical Estimation

Author: P. F. J. LERMUSIAUX

This paper introduces an efficient scheme for data assimilation in nonlinear ocean atmosphere models via ESSE approach. The main goal of this paper is to develop the basis of a comprehensive DA scheme for the estimation and simulation of realistic geophysical fields. The main concept, or whole flow, of this paper is depicted as a figure below:

ESSE flow

Dynamical model: Dynamical Model.gif

Mesurement model: Mesurement Model.gif

Predictability and Model errors: Predictability and Model Errors.gif

F hat.gif: the expected value of f


Link for this paper: http://web.mit.edu/pierrel/www/Papers/mwr2_99.pdf

iii. Parameter Uncertainty in Estimation of Spatial Functions: Bayesian Analysis

Author: Peter K. Kitanidis

This paper analyzes the problem of uncertain parameter and its effect on inference of spatial functions with Bayesian analysis. Parameters are treated as random variables with probability distributions reflecting the known facts. The analysis shows how prior information about the parameters may be combined in the analysis with information in the sample. The result provides insight into the applicability of maximum likelihood versus restricted maximum likelihood parameter estimation, and conventional linear versus kriging estimation.
General Model: General model.gif
x: the vector of spatial coordinates of the point where y is sampled
β: (generally unknown) parameter
fi(x): known functions of the spatial coordinates
ε(x): zero-mean spatial random function; existed random measurement error would be incldued


Prediction model: Prediction model.gif
Prediction model may be defined as finding the PDF
y0: a vector of unknown point or weighted-average values of given observation y
X0: the matrix of deterministic effects for y0

Download this paper: parameter uncertainty in estimation of spatial functions, bayesian analysis

iv. Adaptive Sampling Using Feedback Control of an Autonomous Underwater Glider Fleet

Author: Edward Fiorelli, Pradeep Bhatta, Naomi Ehrich Leonard

This paper presents strategies for adaptive sampling using Autonomous Underwater Vehicle, simply AUV, fleets. The main idea is the use of feedback that integrates distributed measurements into a coordinated mission planner. The cooperative gradient climbing is intended to allow the glider fleet make use of observational data and therefore overcome errors in forecast data.

Link for this paper: http://www.princeton.edu/~naomi/uust03FBLSp.pdf

v. Cooperative Control of Mobile Sensor Networks: Adaptive Gradient Climbing in a Distributed Environment

Author: Petter Ögren, Edward Fiorelli,and Naomi Ehrich Leonard

This paper presents a stable control strategy for groups of vehicles to move and reconfigure cooperatively in response to a sensed and distributed environment. It focuses on gradient climbing missions in which the mobile sensor network seeks out local maxima or minima in the environmental field. The network can adapt its configuration in response to the sensed environment in order to optimize its gradient climb.

Link for this paper: http://www.princeton.edu/~naomi/OgrFioLeoTAC04.pdf

vi. Adaptive Sampling for Estimating a Scalar Field using a Robotic Boat and a Sensor Network

Author: Bin Zhang and Gaurav S. Sukhatme

This paper shows an adaptive sampling algorithm for a mobile sensor network to estimate a scalar field. The data from robots are used to estimate the scalar field. It also explains how the IMSE and the second derivatives of the phenomenon investigated are related to each other. In this paper, the estimation is based on local linear regression, the non-parametric regression where the predictor does not have the fixed form but the predictor is going to be constructed by the information gathered from the data. Of many non parametric estimators, this paper deals with the Kernel estimator.

Basic Model: Basic model.jpg

Y = scalar response

m(x) = function to be estimated

LLR estimator:
LLR estimator.jpg

IMSE of LLR estimator: IMSE of LLR.jpg

Link for this paper: http://cres.usc.edu/pubdb_html/files_upload/524.pdf

vii. Consensus Filters for Sensor Networks and Distributed Sensor Fusion

Author: Reza Olfati-Saber, Jeff S. Shamma

This paper introduces a distributed filter that allows the nodes of a sensor network to track the average of n sensor measurements using an average consensus based distributed filter called consensus filter. This consensus filter is very important in solving a data fusion problem. The objective of this algorithm mentioned in this paper is to design the dynamics of a distributed low-pass filter that takes u as an input and y = x as the output whose property is that asymptotically all nodes of the network reach an ε-consensus regarding the value of signal r(t) in all time t. This paper also introduces the various properties of this distributed filter.

Consensus Algorithm: Consensus algorithm.jpg

Sensing Model: Sensing model.jpg

Dynamic Consensus Algorithm: Dynamic consensus algorithm.jpg

Link for this paper: http://www.nt.ntnu.no/users/skoge/prost/proceedings/cdc-ecc05/pdffiles/papers/1643.pdf


Conclusion

As mentioned above, this project consists of two main parts; hardware of e-pucks and the theoretical research. The new XBee Interface Extension Board design was tested, and we found out that it does not have any problem. In addition, the black dot pattern of the e-pucks are upgraded to LED patterns. The advantage of this improvement is that the machine vision system can recoginize each e-puck no matter where the e-pucks are located. The color of the background also does not affect the vision system. However, we had to move the color sensor to the LED pattern board since the LED pattern board will block the sensor if the sensor is located in the XBee Interface Extension Board. Thus, we now consider the light interference between the LEDs and the color sensor. In the light interference test, we found out that the color sensor is affected by the light from LED. However, since we used much brighter LEDs in our light interference test than the LEDs used for the LED pattern board, we have to do more experiment on this in order to have more accurate interference data.

For the theoretical research part of the project, we found a few algorithms to process the data collected by the color sensor and estimate the environment, as listed above. Some algorithms uses a similar and related method, and some algorithms uses unique method. By comparing those algorithms, we will find the best method which can be applied to the Swarm Robot Project to process the data collected by the color sensor.