Difference between revisions of "PIC32MX: XBee Wireless Round-trip Latency"

From Mech
Jump to navigationJump to search
Line 8: Line 8:


== Circuit ==
== Circuit ==
[[Image:Lab5.2010.Receive.Crct.png|Thumb|150|right]]

The following diagrams depict the circuit we used for our experiments. The theory behind the circuit is simple. The transmitter PIC TX pin is connected to the XBee RX pin. The XBee broadcasts the signal. The receiver XBee's RX pin is connected to the PIC's TX pin. The receiver PIC's RX pin is then connected to the XBee's TX pin.
The following diagrams depict the circuit we used for our experiments. The theory behind the circuit is simple. The transmitter PIC TX pin is connected to the XBee RX pin. The XBee broadcasts the signal. The receiver XBee's RX pin is connected to the PIC's TX pin. The receiver PIC's RX pin is then connected to the XBee's TX pin.
[[Image:Lab5.2010.Transmt.Schmt.png|thumb|300px|Transmitter Circuit|right]


== Code ==
== Code ==

Revision as of 21:11, 13 February 2010

Original Assignment

Your assignment is to set up one PIC32 to send data to another using XBees for wireless RS-232 comm. One PIC will send a series of numbers; the other PIC will receive them and echo them back; and the first PIC will time the total time to send and receive back. To time, the first PIC can set a digital pin high, then set it low again when the original sent data is correctly received. It could also keep track of the count of a counter-timer. You can time how long it takes for the round-trip using an oscilloscope or by reading the counter-timer. You should try this for different baud rates and a couple of different sizes (in bytes) of the message. How low can you get the total round-trip time while guaranteeing low data loss?

Overview

Summarize briefly what the page is about.

Circuit

150

The following diagrams depict the circuit we used for our experiments. The theory behind the circuit is simple. The transmitter PIC TX pin is connected to the XBee RX pin. The XBee broadcasts the signal. The receiver XBee's RX pin is connected to the PIC's TX pin. The receiver PIC's RX pin is then connected to the XBee's TX pin.

Code

Transmitter Code

The code below is for the transmitter XBee chip. Note that the message string sent included only one period and was placed at the end. The program scans the message it receives looking for that period, so it knows that the whole message was received.

/********************************************************************** 

     Transmitter Code
     Lab 5: High Speed XBee Latency
     George Randolph
     Nathan Hirsch
     10 February 2010

This code is for the TRANSMITTER XBee chip.  It takes a string of characters and 
sends them from the PIC to the XBee and broadcasts it out into the world.  The 
reciever chip should receive the message and echo it back to the transmitter.  At
the point when the transmitter first broadcasts the message, a pin on the PIC is 
set to high.  When the message is successfully echoed back, that pin is set low 
so the whole process can be timed using an oscilloscope.

**********************************************************************/


// ****** Includes 
#include "HardwareProfile.h"

// ****** Constants
#define DESIRED_BAUDRATE    	    (115200)	      // The desired BaudRate Note: This must be changed when changing the XBee chip BaudRate
#define PIN_D1			LATDbits.LATD1        // These commands format pins D1-D4 as digital outputs.
#define PIN_D2			LATDbits.LATD2
#define PIN_D3			LATDbits.LATD3
#define PIN_D4			LATDbits.LATD4

// ****** Variables
unsigned int Time;
char RS232_Out_Buffer[64];  			      // The buffer may be changed if lots of data is being sent at a high BaudRate
char message;


// ****** Function Declarations
void initInterruptController();

// ****** Main Function
int main(void)
{
	int	pbClk;
	//initUART2(pbClk);
	
	// Configure the system performance
	pbClk = SYSTEMConfigPerformance(SYS_FREQ); 
	
	mInitAllLEDs();
		
		// define setup Configuration 2 for OpenUARTx
		// IrDA encoded UxTX idle state is '0'
		// Enable UxRX pin
		// Enable UxTX pin
		// Interrupt on transfer of every character to TSR 
		// Interrupt on every char received
		// Disable 9-bit address detect
		// Rx Buffer Over run status bit clear

	#define config2		UART_TX_PIN_LOW | UART_RX_ENABLE | UART_TX_ENABLE | UART_INT_TX | UART_INT_RX_CHAR | UART_ADR_DETECT_DIS | UART_RX_OVERRUN_CLEAR
	
	// Open UART2 with config1 and config2
	OpenUART2(config1, config2, pbClk/16/DESIRED_BAUDRATE-1);	// calculate actual BAUD generate value.

	// Configure UART2 RX Interrupt with priority 7
	ConfigIntUART2(UART_INT_PR7 | UART_RX_INT_EN);

	// Must enable glocal interrupts - in this case, we are using multi-vector mode
        INTEnableSystemMultiVectoredInt();
 	
	//Set D1, D2, D3, and D4 as a digital output
	LATD |= 0x001E; TRISD &= 0xFFE1;


	while(1) //let interrupt handle the UART
	{ 
		if (swUser) // swUser NOT pressed
		{
		// Turn off all the lights to show that the message has not been sent 
		mLED_0_Off();
		mLED_1_Off();
		mLED_2_Off();
		mLED_3_Off();
		PIN_D1 = 0;
		}
		else
		{
		// Turn on all the lights to show that the message was sent	
		mLED_0_On();
		mLED_1_On();
		mLED_2_On();
		mLED_3_On();
       	PIN_D1 = 1; 			    // Set the pin high to begin the clocking 
		putsUART2("1234.\r\n");     // This is where the message goes.  Note the period at the end of the message
		break; 			    // Code only sends the stuff in UART2 ONE time.  
		}
		
	}
   return 0;
 }
 
 
// **** Interrupts

// UART 2 interrupt handler and is set at priority 7
void __ISR(_UART2_VECTOR, ipl7) IntUart2Handler(void)
{ 
	// Is this an RX interrupt?
	if(mU2RXGetIntFlag())
	{
		// Clear the RX interrupt Flag
	    mU2RXClearIntFlag();

		message = ReadUART2();
		mLED_3_On();

		// Toggle LED to indicate UART activity
		if (message == '.') 			      // Note this is the last portion of the message we sent.  
		{
		     PIN_D1 = 0;		              // Put the Pin to low to finish the clocking
		     // Toggle some LEDs to show that the message was received correctly.  
		     mLED_0_Off();
		     mLED_1_Off();	
		}
	}

	// We don't care about TX interrupt
	if ( mU2TXGetIntFlag() )
	{
		mU2TXClearIntFlag();
	}
}

Receiver Code

The code below is for the receiver XBee. It takes the message sent by the transmitter and echoes it back to the transmitter.

/****************************************************
	Receiver Code
	Lab 5: High Speed XBee Latency
	George Randolph
	Nathan Hirsch
	10 February 2010
	
***************************************************/

//*** Includes
#include "HardwareProfile.h"

//*** Constants 
#define DESIRED_BAUDRATE    	(115200)      // The desired BaudRate.  Note this must change if the XBee chip's BaudRate is changed


//*** Main Program
int main(void) 
{
	int	pbClk;
	unsigned char data;						// The variable that will assing the things to when it reads the UART
		
	pbClk = SYSTEMConfigPerformance(SYS_FREQ);

	mInitAllLEDs();
	
	#define config1 UART_EN | UART_IDLE_CON | UART_RX_TX | UART_DIS_WAKE | UART_DIS_LOOPBACK | UART_DIS_ABAUD | UART_NO_PAR_8BIT | UART_1STOPBIT | UART_IRDA_DIS |
                        UART_DIS_BCLK_CTS_RTS| UART_NORMAL_RX | UART_BRGH_SIXTEEN  
	#define config2	UART_TX_PIN_LOW | UART_RX_ENABLE | UART_TX_ENABLE | UART_INT_TX | UART_INT_RX_CHAR | UART_ADR_DETECT_DIS | UART_RX_OVERRUN_CLEAR
	//OpenUART1( config1, config2, pbClk/16/DESIRED_BAUDRATE-1);	// calculate actual BAUD generate value.
	OpenUART2( config1, config2, pbClk/16/DESIRED_BAUDRATE-1);	// calculate actual BAUD generate value.
		
	while (1) 
	{ 
		while(!DataRdyUART2());	     // Wait for data in the UARTRx
      	data = (char)ReadUART2();	     // Read data from Rx and assign it to "data"
		
		while(BusyUART2());	     // Wait till the UART transmitter is free
      	putcUART2(data);		     // Write data into Tx.

		if(data == '.')		     // If the data string matches what we sent, turn the lights on
		{	
			mLED_0_On();
			mLED_1_On();
			mLED_2_On();
			mLED_3_On();
		}
		else 	// If the received data doesn't match what was actually sent, only turn on two lights to show that some data was received, just not the right kind
		{
			mLED_0_On();
			mLED_1_On();
			mLED_2_Off();
			mLED_3_Off();
		}
   }
}

Notes

The message string that was sent ended in a period and there was only one period in the whole message string. We used this to assure that the entire string was read before assigning the digital pin that clocked the entire transfer process to low.