Difference between revisions of "NU32 Electronics and Mechatronics Kits"

From Mech
Jump to navigationJump to search
Line 2: Line 2:


==Minimum Electronics Kit==
==Minimum Electronics Kit==
We recommend this kit for simple interfacing with the NU32, as described throughout the book.
We recommend this set of parts for simple interfacing with the NU32, as described throughout the book. These are available from many vendors; below are some examples where they can be purchased.
* [https://www.jameco.com/webapp/wcs/stores/servlet/Product_10001_10001_127862_-1 a wire stripper] and [https://www.jameco.com/webapp/wcs/stores/servlet/Product_10001_10001_36792_-1 22 AWG solid hook-up wire], typically including black (ground), red, and at least one other color; alternatively you can use a [https://www.jameco.com/webapp/wcs/stores/servlet/Product_10001_10001_19290_-1 wire jumper kit (a pre-cut assortment of wires)]
* a wire stripper
* [https://www.jameco.com/webapp/wcs/stores/servlet/Product_10001_10001_2131127_-1 a multimeter]
* a multimeter
* a selection of breadboard-ready 1/4 W through-hole resistors (for example, [http://www.digikey.com/product-detail/en/RS225/RS225-ND/7110 a kit like this] or individual resistors between 100 ohms and 10K ohms should suffice)
* 22 AWG solid hook-up wire, typically including black (ground), red, and at least one other color
* a selection of breadboard-ready 1/4 W through-hole resistors, but at least ('''these resistances''')
* a selection of breadboard-ready through-hole capacitors (0.1uF and 0.01uF should suffice)
* [http://www.digikey.com/product-detail/en/SFH%20310%20FA-2%2F3/475-1444-ND/1228087 SFH 310 FA-2/3 NPN phototransistor]
* a selection of breadboard-ready through-hole capacitors (e.g., ceramic), but at least ('''these capacitances''')
⚫
* [http://www.digikey.com/product-detail/en/WP7113SRC%2FDU/754-1274-ND/1747673 Kingbright WP7113SRC/DU red LED]]
* [[Media:SFH310.pdf|OSRAM SFH 310 NPN phototransistor]]
⚫
* [[Media:WP7113SRC-DU.pdf|Kingbright WP7113SRC/DU red LED]]

I think we can collect together several of the items above into carts and share. Also give disclaimer that these are just examples; these or similar items can be ordered from many vendors.


==The Brushed DC Motor Control Kit==
==The Brushed DC Motor Control Kit==

Revision as of 16:25, 15 January 2016

To complete projects in the book "Embedded Computing and Mechatronics with the PIC32 Microcontroller" (Lynch/Marchuk/Elwin, Newnes 2015), we recommend the following "kits."

Minimum Electronics Kit

We recommend this set of parts for simple interfacing with the NU32, as described throughout the book. These are available from many vendors; below are some examples where they can be purchased.

The Brushed DC Motor Control Kit

These items are needed to complete the projects associated with a brushed DC motor.

  • a brushed DC motor with no gearhead that draws less than 1 A at stall when powered by 6 V, with an incremental encoder (as many counts per revolution as possible, preferably at least hundreds). No gearhead makes it easier to characterize the motor without having to worry about high friction in the gearhead. You can search surplus sites for such motors or try these recommendations.
  • a 6 V battery pack to power the motor (6 V is not critical; other voltages are possible, provided the motor does not draw much more than about 1 A at stall)
  • 20 ohm 5 W power resistor
  • the motor control board, consisting of a TI DRV8835 H-bridge chip, the MAX9918 current-sense amplifier, and a PICxxx? encoder counter chip that speaks SPI
  • a motor mount to mount the motor securely to the table
  • an inertia bar to attach to the motor to vary its load

Useful Optional Components

The following equipment is used in code samples in the book.

Other Components Referenced or Used in the Book

These components, referenced in the book, can be sourced from various suppliers:

Retrieved from "https://hades.mech.northwestern.edu//index.php?title=NU32_Electronics_and_Mechatronics_Kits&oldid=23675"