NU32: What is in the NU32 Kit

THIS PAGE REFERS TO A PRE-RELEASE VERSION OF THE NU32 PIC32 DEVELOPMENT BOARD. FOR INFORMATION, SAMPLE CODE, AND VIDEOS RELATED TO THE PRODUCTION VERSION (2016 AND LATER), AND TO THE CORRESPONDING BOOK "EMBEDDED COMPUTING AND MECHATRONICS WITH THE PIC32 MICROCONTROLLER," VISIT THE NU32 PAGE.

The NU32 kit.

The NU32 kit contains everything necessary to begin programming the NU32 board. Check to make sure your kit contains the items listed below.

Components in the kit:

Picture	Description	Link
The NU32	NU32 in 2 breadboards
USB Cable	1 m USB cable, A male to mini B male	Datasheet
9V Power Supply	6V wall power supply, 1A, 2.1mm ID x 5.5mm OD, 6W, center positive. From CUI Inc.	Datasheet
16x2 Character LCD	LCD, 16x2 characters, using parallel communication	Datasheet
Pushbutton	Momentary NO pushbutton.	Datasheet
Resistors	A few of the following 1/4W resistors: (in ohms) 1, 10, 33, 100, 300, 1k, 3.3k, 10k, 33k, 100k, 330k, 1M
Capacitors	A few of the following capacitors: (in F) 10p, 100p, 1n, 0.01u, 0.1u, 1u
Potentiometers	2 potentiometers: 10k ohm
LEDs	Red super bright 5mm LED	Datasheet
Phototransistors	SFH 310 visible spectrum phototransistor	Datasheet
Wirestrippers	Wire strippers, for 30, 28, 26, 24, 22, and 20 AWG wire. Can also be used as pliers and to cut wire. These will get dull or mashed up if you try to cut anything other than wire	Sparkfun wire strippers
Wire	6 colors of ~6" sections of 22 AWG solid core wire (red, white, yellow, green, black, blue)	no link
DT9205A Multimeter	Any small multimeter, doesn't have to be this brand.

Components in nScope kit:

Picture	Description	Link
Micro USB cable	A micro USB cable.
nScope in a breadboard	nScope in a 830 tie points.	[1]

Components in the motor kit:

Picture	Description	Link
Hitachi motor with 99 cpr encoder	Hitachi motor with 99 cpr encoder, Red=5V, Black=Gnd, Blue=channel A, White=channel B	NU32: Using the dsPIC33FJ12MC201 QEI to SPI board
The dsPIC33FJ12MC201 breakout board	Breakout board for the dsPIC33FJ12MC201	NU32: Using the dsPIC33FJ12MC201 QEI to SPI board, Datasheet
The MAX9918 current sensor breakout board	Breakout board for the MAX9918	NU32: Using the MAX9918 current sensor, Datasheet
The TB6612 breakout board	Breakout board for the TB6612 h-bridge	NU32: Using the TB6612 H-Bridge, Datasheet
Hitachi motor with mount and inertia bar	Angle bracket and clamp to mount Hitachi motor to desk, 12" aluminum inertia bar with thumb screw and heavy washers	none
The EXI S1123 9g RC servo	EXI S1123 9g RC servo, 0.75ms to 2.4ms pulse at 50Hz. Pinout: Brown=GND, Red=6V battery, Orange=Signal	From HobbyPartz, NU32: Driving RC servo motors
Stepper motor	Stepper motor, 48 steps per revolution, 3:25 gear reduction	From All Electronics, NU32: Driving a stepper motor