Difference between revisions of "EDI Bootcamp"

From Mech
Jump to navigationJump to search
(Replaced content with "Welcome to the Mechatronics portion of Bootcamp! <video width="400px" controls> <source src="solder.mp4" type="video/mp4"> Your browser does not support HTML5 video. ...")
Line 1: Line 1:
Welcome to the Mechatronics portion of Bootcamp!
Welcome to the Mechatronics portion of Bootcamp!


<video width="400px" controls>
Make sure your kit has the following items:
<source src="solder.mp4" type="video/mp4">
* Arduino Uno ([http://www.sparkfun.com/products/9950])
Your browser does not support HTML5 video.
* USB A to B cable (B has a large, square end)
</video>
* 850mAh LiPo ([http://www.sparkfun.com/products/10718])
* Sparkfun LiPo charger and 5V boost board ([http://www.sparkfun.com/products/10300])
* USB A to micro cable (micro has a tiny end)
* RC servo motor
* 3 axis accelerometer ([http://www.pololu.com/catalog/product/1246])
* 8ohm speaker ([http://www.sparkfun.com/products/10722])
* Pushbutton
* Flex sensor ([http://www.sparkfun.com/products/10264])
* Force sensitive resistor ([http://www.sparkfun.com/products/9375])
* Breadboard


Also available are 5mm super bight LEDs in blue, red, green, yellow and white, IR LEDs, IR sensitive phototransistors, red sensitive phototransistors, small RC servo motors, and tiny vibration motors.


The Mechatronics Lab has 6 workstations, each with power supply, multimeter, function generator, oscilloscope, soldering iron, wire, wire strippers and cutters, solder, and a PC with the Arduino software installed. The white cabinets contain resistors, capacitors, potentiometers, and a variety of useful ICs.


You can learn more about the Arduino on the website [http://www.arduino.cc/]

You can download the Arduino website for PC, MAC or Linux at [http://arduino.cc/en/Main/Software]


A nice Arduino tutorial is at [http://www.ladyada.net/learn/arduino/index.html] (uses a slightly older version of the Arduino board, but otherwise is fine)


The [[Media:NU32v2_stripchart.zip | NU32v2 Stripchart plotting tool]] is useful for plotting data on your computer.


Here is the code on the demo Arduino :
<pre>
/*
Example Arduino code for NU EDI Bootcamp 2011

Pins used:
0 - serial rx, hardwired on the board, so don't use it for anything else
1 - serial tx, hardwired on the board, so don't use it for anything else
2 - button
5 - pwm for blue led
6 - pwm for yellow led
7 - vibration motor
8 - speaker, for use with tone() function -> this will mess up
pwm on pins 3 and 11
9 - pwm for the rc servo
A0 - accelerometer X
A1 - accelerometer Y
A2 - accelerometer Z
A3 - flex sensor
A4 - pressure sensor
*/

// include files here
#include "pitches.h" // so that we can play notes, not used here
#include <Servo.h> // to control the rc servo motor

// define global variables here
Servo myservo;
int X, Y, Z, flex, pressure;

// setup() runs once,
// use it to initialize functions and variables
void setup() {
Serial.begin(115200); // setup the serial port to talk at 115200 baud
myservo.attach(9);
pinMode(2, INPUT); // setup pin 2 as an input for the switch
pinMode(7, OUTPUT); // setup pin 7 as an output for the vibration motor
}

// loop() runs forever,
// put your code in here
void loop() {
X = analogRead(A0); // read the value, returns 0-1023 for 0-5V
Y = analogRead(A1);
Z = analogRead(A2);
flex = analogRead(A3);
pressure = analogRead(A4);
if (digitalRead(2)) {
int pos = map(Y, 0, 1023, 0, 180); // change the full range of the sensor
// to the full range of the servo
myservo.write(pos); // pos is the angle of the servo, 0-180 degree
int freq = map(Z, 0, 1023, 31, 5000);
tone(8, freq); // 8 is the pin, freq is the frequency to play
int blue = map(flex, 0, 1023, 0, 255);
analogWrite(5, blue);
int yellow = map(pressure, 0, 1023, 0, 255);
analogWrite(6, yellow);
digitalWrite(7, HIGH); // turn on the vibration motor
}
else {
noTone(8); // turn off the sound
digitalWrite(7, LOW); // turn off the vibration motor
// if the button is not pushed, send the analong values to the computer
// divide by 2 because Stripchart can only show numbers 0-512
Serial.print(X/2);
Serial.print(" ");
Serial.print(Y/2);
Serial.print(" ");
Serial.print(Z/2);
Serial.print(" ");
Serial.print(flex/2);
Serial.print(" ");
Serial.println(pressure/2);
}
delay(20); // wait this many ms before going again
}
</pre>


The functions you can use in your code are listed at [http://arduino.cc/en/Reference/HomePage]


You can power your Arduino off USB power while testing, or using the 3.7V LiPo battery with the LiPo Charger/Booster board to go mobile. From the Boost board, connect GND to the Arduino ground, and VCC to the Arduino 5V.

'''WARNING 1''' Do not connect the USB and battery to the Arduino at the same time

'''WANRING 2''' Do not pull the battery out of the charging board by the wires, try to pull it out by the white plastic connector

Revision as of 11:35, 5 September 2014

Welcome to the Mechatronics portion of Bootcamp!

<video width="400px" controls>

 <source src="solder.mp4" type="video/mp4">
 Your browser does not support HTML5 video.

</video>